The Ruger 10-22 is the most widely sold rifle in North America
The Ruger 10/22 is perhaps the most popular .22 LR calibre rifle ever invented. Yes, Canada happens to have scads of no longer produced Canadian manufactured Cooey .22 rifles, but overall with sales volumes and sheer commonness, Ruger Firearms’ nearly iconic 10/22 has sold more units, spawned off more accessories, and has been the mainstay of nearly all shooters with a .22 rifle. In today’s instalment of Tactical, Practical and Fantastical, we take a look a one of the myriad of aftermarket accessories for the 10/22. TPF will cover the Nomad stock, manufactured by Pro-Mag Industries under the Archangel line of stock replacements. For those readers who are unaware of Pro-Mag Industries, the company initially started as an aftermarket magazine supplier for numerous makes and models of firearms. Pro-Mag has since evolved into one of the leading aftermarket stock and firearm accessory manufacturers in North America. The Archangel product-line is the newest addition to Pro-Mag’s repertoire and encompasses a variety of rifle makes and models with these alternate stock chassis’. In this specific case this aftermarket stock transforms any 10/22 into a near clone, visually, of the Heckler & Koch G-36K Carbine.
ProMag Industries has created a very interesting stock kit for the 10-22
Sights are not optional and must be removed to install the kit properly
Due to the widespread availability and popularity of the iconic Ruger 10/22, it is the focus of multitudes of aftermarket accessories and gear. The Archangel Nomad conversion kit is just one of the many offered for 10/22′s but this kit does completely change the silhouette and physical size of the firearm by fully encapsulating the 10/22 in a shroud manufacturered from reinforced polymer. In order to mount the kit you do need to do some alterations to the standard 10/22 rifle. These include the following steps:
Other than the main Nomad chassis/stock, there are several additional pieces that are required for a complete build
With the new magazine release and bolt hold-open lever installed in the trigger group, assembly is ready to commence
TPF would like to recommend that if you do decide to install this kit, that you take some time prior to installation to thoroughly clean every nook and cranny of your 10-22 rifle. The installation of the Archangel Nomad stock is pretty straight forwards other than the trigger assembly rework. The barrelled receiver is installed into the lower stock portion with the cross-bolt safety put into a middle position. The fit may require some inner material removal to accomodate larger barrel blocks used on some 10/22′s. but once installed, the receiver is secured via the original stock retaining screw.
The 10/22 receiver is held into place by the standard retaining screw just in front of the magazine well.
The upper portion of the stock kit has three attachment points which consist of seven (7) socket head cap screws. A single large button head screw secures the rear portion to the top of the lower Pro-Mag stock component with a pair of screws securing at the front of the lower component. Four small bolts are then used to secure the upper stock portion to the 10/22 recieiver (in place of the previously removed scope rail). That was the difficult installation areas, which is telling as it is very straight forward to assemble. Slide on and secure the forearm and the upper rail with the remaining bolts and associated hardware provided and the your 10/22 now has the facade of a Heckler & Koch G-36K Carbine, with a slightly extended barrel.
The secondary piece uses four small bolts (via the receiver’s scope rail mounting holes) and a trio of larger bolts to affix the top half of the G-36K shell
Drift punch the sights to the left (away in the image) to remove
The final component for mounting onto the 10/22 is the barrel attachment. Pro-Mag includes two options for the Nomad, both which require the removal of the front sight as mentioned earlier. The first option is an aluminum four prong flash hider for the more aggressive look and the second option is the fake silencer sleeve. Both are a tight fit over the barrel and corresponding front sight, but the included roll pin firmly secures the respective sight into position with nary a wobble or wiggle. This is the ONLY true issue that TPF had however with this installation. The four prong flashhider has a blind hole for the retaining roll pin, which means that removal is impossible without some form of metalworking involved.
Snugly fitted over the front sight mount and kept in place with a roll pin, this flash hider is one of the two included options for the barrel aesthetics
The completed installation of the Nomad does indeed make a 10/22 into a formidable looking G-36K clone, and the included 25 round magazines have a full sized shroud which makes them complete the appearance. There are some additional included features which are most likely overlooked on cursory glances. The attached upper picatinny mount, while primarily manufactured from polymer has an integral aluminum stiffener moulded inside for very good rigidity and minimal flexing. The included iron sites are surprisingly robust and working with the rear sight being adjustable for both windage and elevation, and incorporating two aperatures of different sizes and a shrouded fixed front post. Both front and rear sights are removable but should not interfere with most optics. The front underside picatinny rail is much the same as the upper one and comes with an aluminum sling clip mount which is removable/adjustable. The stock itself masses only 1.4kg (3.0 lbs) and has numerous quick detach sling swivel mounting points on both left and right sides.
The G-36 skin completely installed. Note the pair of Pro-Mag 25 round magazines, one which has the shroud to complete the G-36 imagery
Just like the original it copies, the Nomad includes a folding stock
What kind of G-36K would be complete without a folding stock, and this conversion kit does just that. The completed Nomad 10/22 is fully functional with the stock in extended or collapsed position. The Pro-Mag Nomad magazines, with and without the shrouds, functioned very well with no feed issues that were not ammunition releated (misfires). Original Ruger ten (10) round capacity magazines feed and were removed from the gun without issues and some aftermarket 25 round magazines were successfully tested as well. With that being said it is unlikely, due to the G-36K magwell shape that any teardrop shaped magazines or drum magazines for the 10/22 will have enough clearance to be installed fully, however TPF did not have the opportunity to test these hypotheses.
Hidden compartments in the body and in the handle
Like the old TV commercials, there is more! The Nomad does not waste any unused space as it incorporates a pair of storage areas in the lower half of the reciever. The compartment in the grip is accessible all the time and is typical in size for an optic’s batteries or a small cleaning kit. The larger compartment is only accessible when the stock is folded and has nearly enough room to hold a small container of .22LR ammunition (nearly 50 rounds). The entire process of taking your existing Ruger 10/22 and fully installing this kit will take less than two hours if you have the proper tools onhand.
The Archangel Nomad Conversion Stock Kit by Pro-Mag Industries, Model # AAM1022, as reviewed has an MSRP of $204.00 USD, and is available from the fine Canadian establishment, High Caliber Services Corp. which is located in Mission, British Columbia. The kit contains the stock, one 25 round shrouded magazine and the pair of barrel end attachments. As always however it is a question of if you, the reader, feel this product is Tactical, Practical, or Fantastical.
P.S.: in the next day or two TPF will be adding video of an installed Archangel Nomad and checking functionality. Thanks for reading and enjoying TPF-Online!
January 23, 2013 | Categories: Firearms, Firearms accessories | Tags: 10-22, 10/22, aftermarket, archangel, G-36, Hical.ca, nomad, non-restricted, Pro-Mag, ProMag, rifle, ruger, Shooting, stock, TPF, TPF-Online | 2 Comments
Join 47 other followers
Blog at WordPress.com. | The Modularity Lite Theme.
Get every new post delivered to your Inbox.