Feeding the hungry 10/22…. HCMag provides the buffet!

The most common .22 semi-auto rifle in the world; the Ruger 10/22 is a fully customizable firearm which can be modified nearly as much as the AR-15 platform. Relatively cheap to shoot, and fun to shoot, the biggest chore of owning this popular little rifle is feeding it. The .22 long rifle cartridges are notorious for being hard on the fingers for manually loading in past the 10th round, and unless you have a loading tool, the owners of all of these 10/22 magazines likely will not enjoy shooting off a brick (500 rounds) of cheap rim-fire.

So if TPF were to tell readers that there is a new magazine for the 10/22 which has a 25 round capacity, metal feed lips, an easily controlled follower for loading, they may say that is a good thing! Now, on that same magazine, add in a 20 round pocket and a built-in stripper clip to speed load those extra rounds in just a few seconds. The answer is “TAKE MY MONEY!”. There is good news as such a magazine exists in the form of the HC3R magazine from HC Mags. The HC3R is a short form from HC Rapid Rifle Reload, and just from that title the designed product’s end abilities are fairly obvious.

HC Mag’s High Capacity Rapid Rifle Reload magazine

The HC3R magazine actually has several features which have been desired over the years in a 10/22 magazine, and while many aftermarket magazines have one or more of these features, very few, if any have all of them.

1. Larger round capacity than factory magazines
2. Steel feed lips for enhanced durability and increased lifespan of the magazine for feeding ammunition
3. A means of dis-assembly for cleaning the magazine
4. A follower retraction stud, large and lockable into retracted position for spring free loading

Loaded with 25 rounds of .22LR…. But is that it?

Point number one. More rounds readily loaded equals more fun and less time between shots for extended periods and the HC3R has an increased capacity over the original ten (10) round Ruger rotary magazines. While its twenty-five (25) rounds is not among largest capacity magazines available for the 10/22, with one hundred and ten (110) round drum magazines topping those available, it is in line with the majority of aftermarket magazines. The author finds that even a couple dozen rounds can go downrange extremely quickly… What joy!

Stainless steel feed lips

Feed lips are essential for two reasons, they align the cartridge into proper feed positions and ensure a smooth extraction from the magazine into the firearm’s chamber. Older plastic/polymer feed lips have a history of wearing out after a few thousand rounds. Current generations of polymer are improved in durability but steel, or alloy, feed lips are a heavily desired feature as it greatly enhances the lifetime of a magazine before extraction issues become noticeable. HC Mags knew this and incorporated stainless steel feed lips into the HC3R magazine design.

As anyone who shoots thousands of rounds of .22LR will attest, it is a very dirty round which leaves soot and carbon all over, and if left to build up over time, can cause malfunctions and possibly damage to the firearm itself. Magazines are no exception to this and it is a problem that many 10/22 aftermarket magazines fail to address. With extended usage and hundreds, even thousands, of rounds cause magazines to accumulate crud and can even trap water and dirt and it becomes nearly impossible to clean if the magazine is manufactured by fusion processes, such as sonic welding two plastic halves together. The HC3R is a fully bolted together magazine which allows for unparalleled access to clean every nook and cranny from dirt, carbon, and water. A great plus

A well-known feature in most if not all .22LR magazine fed handguns due to the small component manipulation. In this respect the HC3R shines ever so brightly. The huge thumb stud allows for easy tension control as you load ammunition the common method of through the feed lips. You can easily hold it slightly back to allow for the next round to be loaded without worry of misalignment, or lock it completely back at a fully collapsed position. Be aware that rounds, if not inserted properly, can experience misalignment and stack incorrectly with the cartridge perpendicular to the feed lips instead of parallel.

With all of these features, readers may think that these magazines by themselves are very desirable due to the comprehensive features included in the magazine. So here comes the additional bonus. On the side of the magazine is a slot which stores twenty (20) rounds of ammunition. The back component of the HC3R magazine is a speed stripper clip which has two features. The first is as a cover to retain the side stored ammunition when mounted onto the magazine. The second feature is that in addition to aligning loaded rounds in the magazine, it functions as the speed loading strip for quick reloads. So on a fully loaded magazine you will have a total of forty-five (45) rounds available from a single magazine.

Look! An extra 20 rounds in a side pocket!

Spring loaded base for securing the Speed Clip

Notched top for locking the Speed Clip in place

HOW?
Lets start with how to fully load the magazine to maximum capacity by following these steps:

1. Take a quantity of your preferred .22LR ammunition, at least 45 rounds obviously and have them readily available. Have the empty HC3R magazine present.
2. Using the thumb stud on the magazine, retract the spring and follower completely and rotate the stud a quarter turn to lock it into position.
3. Take hold of the speed stripper on the HC3R magazine and pull it away from the magazine. The bottom edge is retained by a spring-loaded guide.
4. Load up 20 rounds into the clip. The speed stripper clip has a pair of guide channels on the inside of its curved profile. The indicator for a total of twenty rounds is easily visible on the inside of the clip. Loading the clip to 20 rounds is very easy and fast with no need to use force or leverage, as the rim of the .22LR round simply slides into the clip’s aforementioned channels. Loaded rounds can only enter and exit the clip on one edge. Ensure that the clip is oriented such to prevent rounds from falling out of the clip due to gravity and movement.
5. Ensuring that the rounds do not fall out of the clip, place the rounds into the side storage pocket of the magazine and slide the clip down and away. Now ensure that the orientation of the magazine is such that rounds do not fall out of the magazine.
6. Load up another 20 rounds into the clip as per step 4.
7. With the magazine positioned to not drop any of the side storage rounds, and so that rounds do not fall out of the clip, insert the clip into the magazine by pushing the bottom end into the spring-loaded guide, and snap the clip into the retaining notch. That is forty (40) rounds so far!
8. Turn the magazine over to ensure rounds in magazine are aligned and release the thumb stud. This is the hardest part to ensure that the rounds sit properly in the feed lips. It is due to the rim overlap and position in the magazine. It took TPF several attempts to get it to work properly every time, by practice makes perfect.
9. Use the thumb stud to relieve tension and load the remaining five (5) rounds to maximum capacity. Total time for the author to load up with practice? Under 90 seconds.

Side pocket rounds retained by the edge of the installed speed clip

Now that the magazine is loaded to full capacity with reserve twenty rounds:

1. Install the magazine, and shoot the first 25 rounds. FUN!
2. Remove the magazine. Why? Spinning the 10/22 around to ensure magazine orientation is sure to give you many funny looks if not yelled at for unsafe firearm manipulation.
3. Using the thumb stud on the magazine, retract the spring and follower completely and rotate the stud a quarter turn to lock it into position.
4. With the magazine held with the stripper on top, take hold of the now empty speed stripper on the HC3R magazine and pull it away from the magazine
5. The side storage has twenty rounds waiting for the clip to slide over. Remember the channels holding the rims of the cartridges? It is that easy.
6. Retract the loaded stripper clip, then with the magazine positioned so that rounds do not fall out of the clip, insert the clip into the magazine by pushing the bottom end into the spring-loaded guide, and snap the clip into the retaining notch.
7. Turn the magazine over to ensure rounds in magazine are aligned and release the thumb stud. Voila! 20 seconds and another twenty rounds ready to shoot.
8. Install the magazine, and shoot the remaining rounds. MORE FUN!

Loading forty-five rounds took 90 seconds. Reloading to use all 45 rounds extended that to under two minutes. How long would it take to load two typical 25 round magazines? Longer than a couple of minutes without any tools or loading accessories. Plus the ten seconds to reload. The HC3R is all about time and thumbs saved in loading magazines so that 10/22 users can enjoy more time putting rounds downrange with the least amount of effort loading. The only negative possible is the width of the magazine with the side pocket which may limit the fit up of some aftermarket 10/22 rifle stocks such as the previously looked at Archangel Stock.

But wait! There’s even MORE!

The Tactical Pack

If your 10/22 is an extremely hungry rifle like the author’s, chewing through a brick of ammunition per session is not unheard of. The balance of buying multiple magazines versus loading them to go through several hundred rounds in a session of rimfire therapy is an eternal dilemma. Or rather was… HC Mag’s understands the need to feed the rimfire hunger, and released the Tactical Pack for the HC3R magazine.

Inside the Tactical Pack

The case itself is thermo-formed with a robust zipper and has both a flexible carry handle as well as a pair of shoulder strap rings on its exterior. The internals are two-fold, with the base filled with EVA foam that is pre-cut to hold all its contents securely. The battle pack contains one complete HC3R magazine, 5 extra speed loader clips with retaining caps, and a quick strip loading box for fast loading of the speed loader clips. Plus multiple pocket cutouts for typical small boxes of .22LR ammunition and a small cutout arrangement for the included set of hex keys for magazine dis-assembly. The upper portion of the case has a zipper closed mesh pocket that encompasses the entire case cover in size, and can be used for targets, bore snakes, and other items that you may wish to include.

The Speed Loading Block – Waiting patiently

The loading box for fast speed strip loading takes couple minutes to fully load up with 100 rounds, five rows of twenty, and setup for usage. Once setup, it takes less than a half minute to load up the five speed loading clips.

Buffet of .22LR ready to load

If fully loaded up with ammunition, the entire case securely holds 545 rounds of .22LR, which makes the Tactical Pack heavy enough to warrant the usage of the shoulder strap included in the package. Of those rounds 245 are ready to use, with an additional 300 rounds in reserve. Unfortunately the reserve ammunition box cut outs are designed for use with paper boxed ammunition, not plastic boxes which are larger and may not fit properly if at all.

The Tactical Pack when fully kitted delivers:

• One fully loaded magazine with side pocket filled. 45 rounds ready to use
• Five fully charged speed loading clips. 5 x 20 = 100 rounds ready to use
• One filled loading box. 100 rounds ready to use
• Six 50 round factory boxes of .22LR. 300 rounds of reserve

That should keep those hungry 10/22 rifles satiated for the meantime, and with the Tactical Pack having an MSRP of $89.00 USD, and available from Canadian vendors such as Wanstalls Online. What do you, the readers think? Is the HC3R magazine and the corresponding Tactical Pack by HC Mags Tactical, Practical, or Fantastical?

April 21, 2015 | Categories: Ammunition, Firearms accessories | Tags: .22LR, 10-22, 10/22, Accessories, clip, HC Mags, HC3R, HCMags, hi-cap, high capacity, magazine, rifle, ruger, speed loader, stripper clip, tactical, TPF, TPF-Online | 3 Comments