4th Annual Canadian SHOT Show Reception
SHOT Show 2017, Day 2 Evening: Wednesday, January 18th
One of the highlights of SHOT Show for TPF-Online is the event hosted by the Canadian Shooting Sports Association (CSSA) and the Canadian Sporting Arms and Ammunition Association (CSAAA). Now for those of you who do not know of either organization, TPF will sum it up very simply.
The CSSA is the Canadian equivalent of the National Rifle Association (NRA) of the United States. Fighting for legal firearms ownership and usage for responsible Canadians. Represents the firearms owners of Canada.
The CSAAA is the Canadian equivalent of the National Shooting Sports Foundation (NSSF) of the United States. Fighting for legal production, distribution, and retail of firearms to the Canadian firearms community. Represents the firearms industry of Canada.
As always, the definitions are subjective as some may not agree with the workings and machinations of either, just like their US counterparts. TPF has been present in some sort of gathering for nearly every SHOT Show for the past eleven years of attending, and it wasn’t until a short few years ago that this event really began to flourish.
Emails were sent out roughly in late August/ early September of 2016 which included an invitation that stated:
The Canadian Shooting Sports Association (CSSA) and the Canadian Sporting Arms and Ammunition Association (CSAAA) are pleased to present the fourth annual Canadian Industry Reception at the 2017 SHOT Show from 6-10 p.m. on Wednesday, January 18, 2017 at Treasure Island Las Vegas.
As a member of the Canadian shooting sports industry, you are invited to participate in this special networking event by sponsoring, attending and inviting your industry guests. The event is designed to showcase the Canadian industry and to provide a social networking opportunity to our industry members.
The origins of this event have evolved from a small social gathering of individuals at timeshares and restaurants into it’s current iteration.
This event has become a great success from when it unofficially started five years ago when the CSSA’s informal Meet & Greet became a sponsored event with a $300 USD budget thanks to a couple select individuals. This gathering, which was to be last of the CSSA’s official Meet & Greets, had an end result of four Texas Mickeys, several cases of pop and water, plus eight extra large pizzas and just shy of twenty (20) representatives of the Canadian firearms industry in a single hotel room for an entire evening. From its humble origins back then in 2013, that marked the first formally organized event specifically for a Canadian attendees of the SHOT Show; this event continues to grow and flourish. This was proven with the 200+ attendees whom signed in at the event entrance, with all but a handful of those hailing from Canada. From a score of individuals to over ten times that in a few years, this event really has become a focal point of Canadian attendees at SHOT Show to interact with their Canadian business partners, associates, colleagues and friends that would otherwise only ever talk via the phone, email, and video-conferences. It becomes an event that these people could network, gain contacts, and just socialize and unwind from the stressful schedule of SHOT.
As the event has grown, so has the requirement for sponsors of the event. It is with many thanks that TPF lists the following sponsors and links to their respective sites, so please feel free to click the links, buy their products or products offered by them and help our industry become even better…
Platinum Level Sponsorship:
- Canadian Shooting Sports Association
- Canadian Sporting Arms and Ammunition Association
- Calgary Shooting Centre
- Korth Group
- North Sylva
Gold Level Sponsorship:
Silver Level Sponsorship:
Bronze Level Sponsorship:
Many thanks must be given to ALL attendees of the CSSA/CSAAA event with many new faces, it was a very good and positive event, and you can bet that there will be another for next year! If you have any questions or comments regarding the event and/or attending please email Mike Duynhoven of the CSSA, he wants feedback and to add Canadian Industry for next year’s event. If you do decide to purchase products from or through one of the event supporters, please reference TPF-Online if you care to help us out. Make sure that all of you enjoy the rest of 2017 and until the next installment, stay safe and have fun!
Some images of the 4th Annual Canadian SHOT Show Reception:
The entrance to the 4th Annual Canadian SHOT Show Reception
A selection of snacks provided thanks to the generous sponsors of the event. Before the doors open
A few moments before the doors officially open
Getting into full swing, the event starts filling up
A different angle from the room in the early evening
Mid-Event, the attendance turnover is steady. As people arrive, others leave for other events and commitments
All aspects of the Canadian firearms industry are represented here
Oh oh. We finally got caught taking images! Many thanks to the CSSA and CSAAA for the opportunity
Several scores of per-registered attendees, plus the reams of invited guests meant that over 220 people attended the 4th Annual Canadian SHOT Show Reception
Once again many thanks to the Canadian Shooting Sports Association and the Canadian Small Arms and Ammunition Association for hosting this event! To give readers and idea of who was there, TPF was able to compile a partial list of Canadian industry registered attendees: (In no particular order, and definitely not complete)…
Air Gun Source, Calgary Shooting Centre, Calibre Magazine, Canada Ammo, CTC Supplies, Grand Power Canada, Gravel Agency, Gryphon Energetics, Korth Group, North Sylva, O’Dell Engineering, Practical Performance Products, Select Shooting Supplies, Shooter’s Choice, Tactical Capital Corp., Tactical Ordinance, Tiger Vac, Trade Ex Canada, Wholesale Sports, Wolverine Supplies, X-Metal Targets, X-Reload, The Gun Blog, Metak Distributing, WCDIA, Nordic Marksmen, S&J Hardware, CGN, McColl Sporting Goods, Aztech Armory, Colt Canada, Sebarms, Canadian Tire, Westside Stores 2012, Premier Shooting Center, Ontario Out of Doors Magazine, Prarie Nation Outdoors, European Arms Distributor, Eastern Outdoor Sales, Surplus Militaire Pont-Rouge, Prefiar, Amplis, Londero Sports, Drummond Shooting, The Evans Group, Al’s Corner Store, Pearl Street Media, Trigger Wholesale, Genesis Enterprise, Compass Safaris Marketing, Outdoor Group Media, CDN Gunworx, Blue Mountain Gunsmithing, Think Insure, Freedom Ventures, Transgressive Media, Outdoor Writers of Canada, Brigadeer Security, Lever Arms, Cadex Defence, True North Arms, National Firearms Association, Excalibur Crossbow, Bowman GunPar, Tetregon Dist., AJ Hobbs Ent., Wild West Shooting Centre, Kolder Canada, E&I Sports, Blackthorn Media, Savminter, Grech Outdoors, Kodiak Defence, HiCaliber Services, Scorpion Outdoors, Nanuk Plasticase, Buck Expert, PGW, Wanstalls
Is this the cure that prevents countless hours of suffering?
“The cure to what?”, may be the first question popping into the thoughts of TPF’s readers. In this case, it is the cure to the single most complained about, biggest headache for anyone who reloads rifle cartridges. Besides the tedious task of collecting range brass and cleaning it through various means, there are many steps to preparing a spent rifle case before ever assembling a new cartridge for use.
The Steps for reloading rifle cartridges:
- Collect spent cases: Go pick up your brass and if you are lucky, everyone elses!
- De-prime cases: Can be done after step #3 depending on cleaning methods and press types
- Clean cases: Degree of cleanliness is dependant on the reloader themselves. Wipe off, dry or wet tumble, ultrasonic cleaning?
- Size cases: Full or neck only sizing is another factor dependant on the reloader’s desires.
- Trimming brass: Cutting to length and possibly chamfering inside and outside of the case neck.
- Re-prime case: By hand or by press
- Powder charge: Check the type of powder, as well as the levels in the hopper/scoop. Also do not under or over charge the case!
- Bullet seating: Make sure your OAL allows proper feeding!
- Bullet crimping: If necessary and do not over crimp!
So the biggest headache? Step 5. Trimming…
Trimming is the simple procedure in cases preparation that involves the shaving of brass down to specifications for most calibres as set out by Sporting Arms and Ammunition Manufacturers’ Institute, aka SAAMI. IF you perform step number 5, there are a huge number of methods available for an equally broad range of retail pricing. However the product on today’s TPF plate for reviewing is the Trim-It II.
The trim-It II as packaged
Direct from the website the features of the Trim-It II are listed as:
- Built-in micrometer adjustment for cut-length control
- Interchangeable die system, allowing you to trim a wide range of cases with one unit
- Adjustable cutting tool with 3-sided carbide blade that allows for a 15 degree inside case mouth chamfer and 45 degree outside chamfer
- Machined from 6061-T6 Aluminum. This baby is built to last.
- 100% Forever (plus 90 days) Guarantee.
- Made entirely in the good ole’ US of A!
The Trim-It II that TPF obtained came is a small, compact cardboard package which contained everything needed to start trimming. OK. Almost everything… Like most reloading apparatuses, the basic unit does not come with the calibre specific components such as sizing dies and the like. This product is no different, and offers calibre specific bearing dies for many of the most common hunting calibres, pistol calibres, and some of the more popular long range benchrest calibres that are used.
What you get in the box, plus a calibre die
The original Trim-It had a micrometer adjustable depth ability and a four bladed flush cutting head that did just that, trimmed cases to the user’s set length. The secret to both the Trim-It and the Trim-It II? The calibre bearing die. For this review, TPF-Online decided to use the ever popular .308 Winchester round for trimming. Having many, many hundreds on hand to be converted from fired brass condition into usable ammunition was just a stroke of luck as we would never just go out and discharge .308 Win by the scores just for reviewing a trimmer… OK, maybe we would… Alright… We did… And it was worth it! So lets start by explaining the components that you receive in the package when a Trim-It II is purchased… Plus the .308 Win Calibre Die.
- Instructions, 2 pages double sided
- Allen keys, 4 of varying sizes (0.050″, 1/16″, 3/32″, and 9/64″)
- The cap/barrel assembly
- 3-way cutter
- Calibre die, .308 WIN (sold separately)
Instructions:
These are likely the cheapest component of the entire set. Now these two pages seem to be simple double sided photocopies that are folded into 1/8 the original size to fit into the box. One page contains the product warranty details and a fillable sheet for returning defective/broken products. The other sheet is the one that is most important to everyone that is reading… A parts list and instructions on how to assemble, tune, and utilize the Trim-It II. The instructions for this are only on a single unfolded side and also contain the instructions for refitting the original Trim-It with the new 3-way cutting head. Opposite the instructions is a parts list diagram of both the Trim-It and Trim-It II.
Allen Keys:
The L-shaped hex drivers for adjustments and locking in components with set-screws. You knew this already however, so not going to say any more on these parts…
Cap/Barrel Assembly:
So the cap serves two purposes, both of which are important for the functionality of the Trim-It II. First is the mount for the 3-Way Cutter that is secured along the cap’s centreline with a set screw. This forces the cap to rotate with the cutter when under power. The second purpose is to act as the threaded mount for the barrel part of the assembly. The barrel houses the Calibre Die, and because it is threaded into the cap, allows for fine distance adjustment for cutting brass to the proper overall length. The barrel has numerous openings which allow adjustment to the cutting head as well as a path through which trimmed shavings can be removed. The barrel has an external o-ring groove which holds the clear polycarbonate sleeve in place to prevent shavings from flying everywhere when in use. A set screw locks the barrel depth into place as well as locking the calibre die into its groove.
The miniature boring head with carbide insert
3-Way Cutter:
The three way cutter is a miniature version of a milling machine’s adjustable boring bar. The cutter insert itself is a simple triangular insert whose corners have been cut to a V shape to trim both inner and outer chamfers and thereby also the length of any brass casing. TPF-Online did not remove the insert, but the V shape is on all three corners of the insert meaning that if you even wear down one of the cutting profiles, you can rotate and have a new cutting profile to be used. Twice… Since these are only trimming brass versus the insert’s carbide, it is likely to last for generations of shooters. The mounting head of the cutter is adjustable itself, with the insert able to be shifted towards or away from the centerline of the cap/barrel. This allows for different diameter necks to be trimmed, but unless you have several of the cutters pre-set, re-adjusting the cutter for each new calibre introduced is required.
Calibre Die:
These are sealed bearings that are modified by machining a custom inner ring to accurately position brass for trimming. These are precision tolerance bearings which are aligned by the barrel groove machined to exacting tolerances. with the outer ring of the die secured with a set screw in the barrel, the inner ring is free to rotate independently of the cap/barrel/cutter assembly.
A .223/5.56 and .308 examples of Calibre Dies available
How it works… Aka steps for using the Trim-It II:
- Install the 3-way cutter into the cap/barrel assembly so that it is as close as possible to the cap and secure with set screw against the flats in the shaft of the cutter.
- Tighten barrel into cap until it stops (“Zero”) back off until you alight the barrel index line with one on the cap. Unscrew barrel for one full revolution and lock in place with a set screw.
- Insert desired calibre die into place in barrel and lock it with set screw.
- Insert desired brass piece into calibre die.
- Loosen cutter set screw and move cutter until it touches neck of brass. Re-tighten setscrew.
- Slightly loosen cutting head set screw and adjust the position of the carbide insert so that the neck edge will touch the base of the V shape cutout on the insert. Re-tighten cutting head set screw.
- Loosen barrel set screw and adjust for height. Re-tighten. Each mark on the cap equals 0.002″ travel.
- Install into a drill, drill press, dedicated rotary tool, etc… Ensure the drill turns clockwise, otherwise cutters will not work properly.
- While drill is running, insert brass case into calibre die. If not trimmed to the right length shut down and adjust barrel as per Step 7.
- Go trim happy… When you don’t hear the inserted brass being trimmed, time to put in the next piece.
It is a lot of work for setting up the Trim-It II, but once the tool is setup, the unit is spectacularly fast in doing it’s job. For those who only have a hand drill however, the entire setup will be hard on the hands.
Pros:
- Fast once setup
- Nearly forty calibres available
- Easily adjusted for OAL
- Ease of cleaning due to the polycarbonate sleeve
- Rock solid
- High quality
- Not expensive like a GTC Giraud Power Trimmer
Cons:
- Adjusting the V-notch could be easier to tune
- Hard on hands if using a hand drill
- Handheld brass case tries to spin while cutting
- Not cheap like a Lee Zip-Trim
Recommendations:
- Table top drill press, or dedicated drive unit for the Trim-It that allows for two hands to manipulate and hold brass.
- Design change for the carbide insert adjustment. Use a fine thread screw for adjusting distance from centre line.
The components ready for assembly and adjustment. Soon to be followed by copious volume brass trimming…
The Trim-It II as reviewed is available from brick and mortar store locations such as Select Shooting Supplies in Cambridge, Ontario. Their listed prices are, at the time of this review, $189.95 CAD for the Trim-It II, and $29.95 CAD for each calibre die. Is the Trim-It II a worthy addition to one’s repertoire of reloading tools? Does it fall under the category of Tactical, Practical, or Fantastical devices for firearms owners? That is a simple question that only YOU, the reader can answer.
TPF-Online wishes to thank Mr. Chris V. for his comments and additional input on this review. Between his efforts and those of TPF-Online, nearly 2000 pieces of .308 Win brass was trimmed in very little time.
It’s the most wonderful time of the year… and for Gunnies, it isn’t Christmas…
It’s the most wonderful time of the year
With the kids jingle belling
And everyone telling you “Be of good cheer”
It’s the most wonderful time of the year
When Andy Williams sang “It’s the most wonderful time of the year” back in 1963, Christmas truly was the most wonderful time of the year. Everybody looked forwards to getting presents from “Santa” and opening up their gifts from the jolly ole fat man. Fast forward just over a half a century to 2015, and the most wonderful time of the year fell during the third week in January as the 37th annual Sporting Hunting Outdoor Trade Show once again graced Las Vegas, Nevada, with yet another larger than life event.
Parking for Media Day, plus buses
It started on Monday, January 19th, under a clear blue sky and temperatures that hovered around a chilly 16º C. Alright, it really is not that chilly to us Canadians, but for Las Vegas, it is wintertime. Thousands of media and buyers attended the tenth SHOT Show Media Day at the Boulder Rifle & Pistol Club (BRPC), located just on the outskirts of Boulder City, NV. Having been to several Media Day events from previous SHOT Shows, BRPC has continued to grow and expand as the annual number of exhibitors has also grown each and every year. Over one hundred and seventy exhibitors were there and catered to roughly a thousand invited media attendees and over five hundred invited buyers, dealers, distributors, and retailers for the day.
From the top of the hill at the “long range” positions, to the right
Opposite direction from the hill top
This year the Monday event was entitled SHOT Show Media and Industry Day and it is the chance to literally try out many firearms “hands-on” and experience directly existing products, new launching products, and prototype future products. A fair chunk of the items on display are not available to the Canadian civilian marketplace due to being categorized as prohibited devices. Compact handguns meant entirely for protecting one’s self, fully automatic or select fire sub-machine guns for law enforcement and military usage while not the norm, were available for ALL attendees to experience. In fact the roughly 1600 media and industry attendees discharged just over a half million rounds downrange from 9:00 am until 4:30 pm. Unsurprisingly contrary to the expectations of those whom are under the impression or belief that guns are inherently unsafe to use, let alone possess; not a single firearms related injury occurred and there were many satisfied smiles amongst the attendees.
The author’s early Christmas present was being able to shoot this APO custom rifle out to 982y. Two words… Hell Yeah!
A Media Day newbie, Keith Beasley, from Canada in the Rough fame, tries out some modern, non-traditional rifles at targets over a 1/2 km away!
However, after the Monday of live fire and big smiles comes Tuesday morning, when the SHOT Show officially begins, the work starts and the long trek ensues. With sixteen hundred and seventy eight (1678) exhibitors this year, that meant that if you were to be able to instantly transport yourself in front of every single booth and instantly launch into conversation with that exhibitor’s representative that you would have exactly 74 seconds of talking to that person. Consider that there are over 19km (~12 miles) of aisles to walk plus lunchtime plus waiting for a representative to talk to and that 74 seconds gets shaved down considerably. That puts it at say 60 seconds per booth with zero waiting and no travel that was not toward the next booth. If someone can ask about a new product and get the representatives to explain it in 60 seconds or less with all questions being answered, then TPF may have a job for you!
Shooting Chrony have been regular exhibitors of SHOT for years
Now Canadians and Canadian Companies at the show are not new. TPF has routinely visited long time CSSA supporter Ms. Esteves for years at the Shooting Chrony Inc. booth at SHOT Show. Other Canadian manufacturing companies have been at SHOT for several years such as Toronto based Flash Fog Defense, and last year’s newcomer to the SHOT Show, Modular Driven Technologies. However there was something different about the 2015 SHOT in regards to Canadian companies being represented at the show.
Cadex Defence was present at SHOT as well.
Greg (l) and Rick (r) representing Canada’s Vault Distribution
Imagine TPF’s surprise when on every single cover of the thick SHOT Show exhibitor listing guidebook is a large sticker denoting VAULT Distribution and their booth location. Now while Vault Distribution was founded back in 2009; 2015 was its first as an official SHOT Show exhibitor. A Canadian company getting pretty much top exposure to every single attendee who grabs that book, and there were tens of thousands of attendees. Simply amazing! TPF stopped by Vault Distribution’s booth throughout the duration of the SHOW to talk a bit with Mr. Steve Ricker and Mr. Greg Zeitler. Like several other Canadian companies, Vault Distribution has attended SHOT Shows in the past seeking out product lines to deal in and thereby bring those products to the Canadian marketplace. For several years now Vault Distribution has been synonymous with firearms from Kel-Tec CNC Industries Inc., but they also deal with SIG Sauer firearms and Trace Optics to name a couple of other brand names. They will likely be bringing in more products and more brand names in the future, at least we at TPF-Online hope so. However, with how busy the Vault guys were, especially in the latter days of the SHOT Show, odds for Vault Distribution doing just that are better than average!
The 2nd Annual Canadian Industry SHOT Show Gathering
As has become tradition over the last several years, the CSSA has held various sized Canadian gatherings during the course of SHOT Show. In 2013 was the beginning of the truly sponsored gathering, with a few supporters tossing in a few hundred dollars for food and drink that year. Last year in 2014, the CSSA hosted the first officially sponsored Canadian gathering and it was a great success. In 2015, the gathering was altered slightly in two ways. The CSSA partnered up with the Canadian Sporting Arms and Ammunition Association (CSAAA), and the event was by “invite” only. Readers will notice that the word invite is in quotes. In 2014 there was a generic posting for the event across every imaginable cost effective medium available, and that included several online forums, and a ton of word of mouth. This time around there was a conscious decision to make the event more geared toward the Canadian industry that was attending the SHOT Show. Businesses were contacted via emails and phone calls and asked if they wished to attend, and were sent initiations via mail. However, even though invitations were distributed, anyone association with the industry was allowed access. It was surprising to see that the CSSA’s rivals, the NFA was allowed into the event as the author knows they did not get sent invitations. As the CSSA hosts stated to TPF, it is a Canadian industry gathering and all were welcome. Kudo’s to the CSSA for not playing the “Invite Only” card, very professional and courteous of them.
The empty room prior
Soon after the doors opened
A special thanks has to go out to the sponsors of the event, it was easily as large as last year’s in attendance, but so many more industry attendees. Noted sponsors at the event were as follows.
Platinum Level Sponsorship:
Gold Level Sponsorship:
Silver Level Sponsorship
- Canada Ammo
- Calgary Shooting Centre
- Interammo Impex
- Marstar Canada
- The Right Edition
- Vault Distribution
Bronze Level Sponsorship
- Ballistic Bowstring
- Firearm Legal Defence
- O’Dell Engineering
- Select Shooting Supplies
- Trade Ex Canada
- Wolverine Supplies
Honourable Mention
Many thanks must be given to ALL attendees of the CSSA/CSAAA event, it was a very good and positive event, and you can bet that there will be another for next year! If you do decide to purchase products from or through one of the event supporters, please reference TPF-Online if you remember.
Alas like Christmas, the SHOT Show only comes around once per year… Which may or may not be a good thing. As stated in past installments, the SHOT Show is brain overload for new attendees, with over a billion dollars of product on display including prototypes, new releases, versions of older stuff, and regular line item products. If you ever get a chance and are able to get access, you should attend at least once to experience just how awesomely huge the industry is… Many thanks for reading here at Tactical, Practical and Fantastical.
Tactical, Practical & Fantastical 